FLUIDA is a gel-like, highly effective, CHC-free scouring paste for the removal of old paint coats. FLUIDA easily dissolves oil paints, synthetic resin and nitro paints, acrylic paints and 2-component lacquers. FLUIDA has a very good depth effect, excellent dissolving and swelling properties and good stability on vertical surfaces.

FLUIDA is a gel-like, highly effective, CHC-free scouring paste for the removal of old paint coats. FLUIDA easily dissolves oil paints, synthetic resin and nitro paints, acrylic paints and 2-component lacquers. FLUIDA has a very good depth effect, excellent dissolving and swelling properties and good stability on vertical surfaces.

FLUIDA is a liquid, highly effective methylene chloride and VOC-free paint stripper for the removal of old paint. FLUIDA easily dissolves oil paints, synthetic resin and nitro paints, acrylic paints and 2-component lacquers. FLUIDA has a very good depth effect and excellent dissolving and swelling properties.

For thorough substrate preparation of heavily soiled ceilings and walls caused by nicotine and greasy soot; exterior facades soiled especially by sulphur dioxide and heating oil must be thoroughly cleaned. SE-1 is also suitable for removing wax from wall surfaces and can also be used in airless devices. Special insulation is not necessary. The hiding power of the paint is fully given.

Highly concentrated in powder form. For easy removal of normal wallpaper, glue paints and smudge-proof binder paint. The new active ingredient dissolves all wallpapers quickly and safely without pretreatment. Special additives ensure that the wallpaper is evenly wetted without the liquid running off.

Removes all ingrain wallpapers (also multi-coated) without any problems even without using the spiked roller, sandpaper etc. Also for removing wallpaper that is difficult to remove, such as textile and vinyl wallpaper. Without use of the spiked roller, even with ingrain wallpaper that has been coated several times, and thus considerably less processing time. Extremely high peeling force due to special additives and therefore no running off on the wallpaper.

Geiger Silicone Joint Remover is a pasty compound which is applied thickly in at least 1mm thickness to silicone sealants and silicone adhesives and removed from a wide variety of substrates by simply wiping.

For the brightening of woods of all kinds. Old woods that have turned black become as good as new again. Oxide wood bleaching powder is ideal for removing discoloration from oak, ash, teak, nut, pine, pitchpine, rosewood, etc. Even woods painted with oil paint regain their natural colour. Highly recommended for the renovation of your sauna. For removing welding edges. OXYD Wood Bleaching Powder has a very strong fungicidal effect, destroying mould and fungi in one step.

NEUTRALAN wood graying gel cleans intensively and removes the greying effect by lightening the wood and restores its natural appearance. It freshens up wood that has been exposed to UV radiation and weathering and enables the greyed wooden surfaces to be restored to their original colour.

NEUTRACID is a highly effective cleaning agent and dissolves lime, grease, rust and cement residue effortlessly. It can also be used for pickling, etching and soldering in metal processing or for roughening galvanized surfaces. Due to its corrosive nature NEUTRACID must be used with extreme caution and the safety instructions must be observed.

PUROL is an alkaline, low-foaming and phosphate-free, water-based intensive cleaner. It serves as a universal cleaning and degreasing agent as well as for the pre-treatment of old coatings and, due to its alkalinity, removes a wide variety of impurities efficiently and safely. The PUROL concentrate is diluted with water before use, depending on the requirements and degree of soiling. The PUROL solution is gentle to the surface and sensitive materials can be cleaned without any problems. Only undiluted application on surfaces made of aluminium, zinc, plastics etc. should be avoided. PUROL was developed especially for machine application. Wherever foam is disturbing, PUROL can be used without hesitation.

NEXOL is an aqueous and multifunctional care concentrate for high-performance and environmentally friendly cleaning, based on renewable raw materials. It serves as a cleaning and degreasing agent and cares and nourishes at the same time. The treated surfaces do not become dull and matt, but regain their original freshness. The NEXOL concentrate is diluted with water before use, depending on the requirements and degree of soiling. The NEXOL solution is gentle to the surface and sensitive materials can be cleaned without any problems. Only undiluted application on surfaces made of aluminium, zinc, plastics etc. should be avoided. NEXOL was developed especially for machine application. Wherever foam is disturbing, NEXOL can be used without hesitation.

NEUTRAMAT is a highly effective solution of inorganic acids for the surface treatment of silicate-bonded substrates and metals. The reaction of NEUTRAMAT with the silicate components creates microscopically small pores, which increases the adhesive strength of a subsequent paint or coating system. The treated surfaces generally meet the requirements of wet slip resistance according to DIN 51130 and BGR 181 (formerly ZH1/571 – slip resistance class R9).

DUROX is a highly effective concentrate for the removal of lime and cement residue (sinter skin) and as a cleaning agent for metal and natural stone. The high efficiency, also in connection with oily and greasy contamination, is based on the low acidity of PH-1. In this way, the adhesion-inhibiting sinter skin (cement residue) or lime residue is removed cost-effectively and the adhesive strength of a subsequent painting or coating system is increased.

NEUTRASOL is a highly effective concentrate for the removal of lime and cement residue (sinter skin) and as a cleaning agent for metal and natural stone. The high efficiency, also in connection with oily and greasy contamination, is based on the low acidity of PH-1. In this way, the adhesion-inhibiting sinter skin (cement residue) or lime residue is removed cost-effectively and the adhesive strength of a subsequent painting or coating system is increased.

NEUTRASAN is a gentle cleaning concentrate on a plant soap basis for regular wiping care of all natural surfaces indoors. With NEUTRASAN the surfaces can be cleaned easily and intensively without damaging the surface. Thanks to the regreasing effect, the materials regain their natural freshness and colour.

The Anti Graffity cleaning agent infiltrates spray paints, paints and felt-tip pens on all solvent-resistant surfaces (such as metal, glass, wood, tiles, unpainted concrete, clinker bricks and natural and artificial stones) and thus serves to remove paint smears and unwanted graffiti. In the case of painted or varnished surfaces, the substrate can also be detached. In the case of non-solvent resistant substrates, compatibility must be checked. It is recommended to protect the cleaned surfaces with Anti Graffity Finish or Anti Graffity Protective Varnish.

It is universally applicable for acid-sensitive or alkaline reacting stone facades. GEIGER facade cleaner is weakly alkaline with a low PH value and therefore not subject to classification according to the Working Materials Ordinance.

The product is used for cleaning, degreasing and pre-treatment of preferably galvanized parts / surfaces. In addition to cleaning and degreasing, treatment with zinc and aluminium cleaner prepares the top layer of the zinc coating, especially in the case of freshly hot-dip galvanised parts, for the subsequent coating. The natural protective coating on weathered galvanized parts is not negatively affected.

For easy cleaning and removal of lime and cement residue, inorganic soiling and flash rust, also in combination with oily and greasy soiling. For cleaning acid-resistant surfaces such as wall and floor tiles, brick and clinker surfaces, porcelain stoneware in sanitary facilities, swimming pools, kitchens, car wash halls, clinker facades. Check compatibility when used on bathroom fittings. Degreasing and strongly dirt dissolving.

Highly effective for the removal of all dispersion stains (even those that have already dried through), dispersion adhesives and adhesive residues from masking tapes. DIP removes all paint stains, dispersion paints, varnishes and oil paints from all solvent-resistant surfaces such as masonry, wood, glass, textile floors, even if they are already thoroughly dry. For plastic and painted surfaces, compatibility must be checked in an inconspicuous place.

Geiger adhesive remover removes all adhesive bonds such as all-purpose adhesive, foam adhesive, wood glue, dispersion adhesive, self-adhesive labels and adhesive residues from masking tapes, etc. Floor covering residues (e.g. compact foam and felt residues) that remain behind when removing can be completely removed with this. Coating residues and adhesives are removed in one operation. Due to the excellent dissolving properties, oils and greases can also be removed from metal, wood, stone and glass.

Easily biodegradable cleaning concentrate for all washable surfaces. Profi-Star cleans strongly and removes difficult to remove dirt of all kinds without etching and thus maintains the natural shine of the surface. Removes all soiling and is 100 % degreasing. Particularly suitable for e.g. painted surfaces, carpet and upholstered furniture, kitchen appliances, plastic surfaces etc. Also suitable for cleaning floors (stone tiles and linoleum), window frames and all washable surfaces.

The highly effective cleaner for all plastic and synthetic surfaces for household, commercial and leisure use. Strongly dirt dissolving and yet surface-friendly, very good biodegradability and non-caustic.

Very suitable for coarse, difficult to remove contaminants such as adhesive residues from films, adhesive tapes and labels. Also for removing grease and oil. Cleans neutrally (pH 7,5) and gently on a variety of surfaces.

Powdery gypsum-based putty, raw materials from selected stone pits and plastic-modified. White when stirred. Ideally suited for repairing large and small cracks and holes on untreated or painted interior surfaces. Adheres to painted substrates. Fast setting time: 30 minutes, layer thickness unlimited. Easy to grind. Suitable for use with screws or nails. Very fine.

Powder filler on the basis of cement, raw materials from selected quarries and plastic-modified. High white when stirred. Ideally suited to quickly and reliably repair large and small cracks and holes on untreated or painted interior surfaces. Quick recoatability. Adheres to all substrates. Fast setting time: 30 minutes, layer thickness unlimited. Easy to grind. Suitable for use with screws or nails.

Powdery putty made of high-quality, bonded mineral fillers. White when stirred. Ideally suited for large-area pre-treatment of damaged, old and uneven interior surfaces. These can be pre-painted or untreated. Up to 5mm layer. Adheres to painted substrates. Time saving: Second shift after 3 hours. Processing time 2,5 hours. High coverage. Easy to process.

Pasty putty with very fine calcium carbonate based fillers. High white when stirred. Ideally suited for the rapid prefilling of damaged or untreated or pre-coated substrates. Manual and airless. Layer up to 5mm. High filling power. No cracking. Adheres to painted substrates. Easy to process.

Powdery putty made of high-quality, bonded mineral fillers. High white when stirred. Ideally suited to create a perfect surface on large painted or untreated surfaces. Up to 1mm - layer. Adheres to painted substrates. Can be painted over after 24 hours. Improves quality of subsequent coats. Easy to process. Extra-white.

Paste-like, airless levelling and smoothing filler for interior use based on calcium carbonate fillers and binders. Highly covering with optimum open time and fast sanding. Suitable for raw or painted substrates such as plaster, plasterboard, exposed concrete, lightweight brick, cement, plaster, etc.

Cement-bound, powdery filler compound, polymer-modified, with high-quality mineral fillers. White when stirred. Ideally suited to quickly and reliably repair large and small cracks and holes on untreated or painted outdoor surfaces. Extraordinary adhesion. Fast setting time - 30 minutes. Can be painted over after 24 hours. Coating thickness unlimited. Highly paid. Suitable for use with screws or nails.

Cement-bound, powdery filler compound, polymer-modified, with high-quality mineral fillers. White when stirred. Ideally suited for levelling out irregularities on dry, untreated or damaged large-area outdoor surfaces. Up to 3 shifts per day. Time saving - second shift after three hours. Can be painted over after 24 hours. Adheres to painted substrates. Easy to grind. Suitable for use with plugs, nails or screws. Weiss.

Powdery and fibre-reinforced exterior putty based on cement and selected mineral fillers and binders. Suitable for filling, repairing and levelling. Very strong adhesion and resistance, permeable to water vapour and quick to paint over (24 hours).

Paste-like putty based on acrylic polymers. Ideally suited for filling and smoothing holes and small defects in a layer in the interior. Filling and smoothing in one layer. Doesn't collapse, no need to grind. Quick recoatable within 30 minutes. High white.

Exterior paste plaster, based on lightweight fillers and resins. Ready to use, fills and smoothes in one go, can be covered after 1 hour.

Linseed oil putty. Ideally suited as a window putty and for repairing cracks in wooden parts before painting. Does not stick to the hands. Permanently elastic. Easy to process. No danger of hairline fractures. Compatible with acrylic paints. Long shelf life in the container.

decomur Super Adhesion Filler is excellently suited for the full-surface filling of ceilings and walls, for filling cracks, joints and holes as well as for gluing and gouging plasterboard and gypsum fibreboards. Synthetic resin and fibre reinforced, optimum adhesion on many substrates, crack-free setting, can be pulled out to zero, even curing in any layer thickness.

Synthetic resin and cement-based plaster for filling holes and cracks, gluing, smoothing, repairing and restoring facades, walls and ceilings. Exterior and interior. Fibre- reinforced. White. Adheres even to blocked substrates such as earthenware and paint without sanding or priming. Can be applied during. Approx. 30 minutes. And from 0 to over 10 cm per coat. Dries without cracks or shrinkage.

Grey, fast-setting special cement for interior and exterior use. For quick repair of chippings, cracks and holes in plaster, concrete, cement screed and similar mineral substrates as well as for fixing and securing building components. Approx. 3 minutes application time, weather and water resistant, quick loadable.

WIEROspac AQUA is a ready-to-use wet room filler. Its grey-blue mineral-based filler is based on the highest quality dolomite marble and has been developed specifically for wall and ceiling surfaces in wet rooms. The higher binder content enables optimum adhesion to a wide variety of substrates with a high load-bearing capacity and hard surface.

Ahrweilit Filler is an easy to use hybrid surface filler for wood and metal in interior areas. It is characterized by high yield and long open time, so that even large areas can be filled without any effort. Overpaintable after 3–4 hours with acrylic, synthetic resin and emulsion paints.

Ahrweissal Kunstharzspachtel is an easy to use filler for wood and metal in interior and exterior areas. It is characterised by particularly easy processing and high yield. Highest covering and filling power. Overpaintable after approx. 12 hours with acrylic, synthetic resin and emulsion paints.

For filling small holes and cracks, for pore removal of new wood and for repairing scratches in well primed metal. Fast drying, good filling capacity and good elasticity. Ahrweitex- Quick Filler can be applied several times in a short time on top of each other. After drying, it can be easily sanded and is characterized by its white color. Maximum wet film thickness 1000 µm.

DUROFIL is a water-dilutable, quick-drying and smooth acrylic fine filler. DUROFIL has a good filling power, can be pulled out easily and remains supple without rolling, even after longer processing (repeated pulling through). After a short drying time, DUROFIL can be applied several times on top of each other and produces a fine, pore-free and stable surface.

Powder putty for the repair as well as for modelling missing wooden parts. Exceptional adhesive strength. Can be carved, planed, sanded, drilled and painted.

SILAFIL is a fast drying, very filling and transparent wood paste based on nitrocellulose. SILAFIL is characterized by excellent adhesion, low volume shrinkage and fast drying. SILAFIL has a good filling power, can be pulled out easily and remains supple without rolling, even after longer processing (repeated pulling through). After hardening, SILAFIL can be sanded, planed, filed or sawed, stained and repainted.

2-component polyester filler for the permanent repair of structures made of wood, mineral and gypsum fibre boards, metal and plastic. Permafix 1190 can be overpainted with all commercially available water-thinnable or solvent- containing 1- and 2-component products.

RUBAPLAST^® is a permanently elastic and shrink-free 2-component filling and modelling compound for filling cracks and holes as well as for patching and shaping. It is characterized by high elasticity, excellent adhesion and sandability as well as low volume shrinkage.

DUROVIT is a ready-to-use, plasto-elastic and age-resistant one-component joint sealant on an acrylic resin basis for interior and exterior use. DUROVIT is characterized by high weather and light resistance and remains permanently elastic over a very wide temperature range from -20° to + 75 °C.

ELOTOP is a ready-to-use, plasto-elastic and age-resistant one-component joint sealant on acrylic resin basis with a structured, rough and plaster-like surface for interior and exterior use. ELOTOP is characterized by high weather and light resistance and remains permanently elastic over a very wide temperature range from -20° to + 75 °C.

ACRYL-W is a ready-to-use, plasto-elastic and age-resistant one-component joint sealant on an acrylic resin basis for interior and exterior use. ACRYL-W is characterized by high weather and light resistance and remains permanently elastic over a very wide temperature range from -20° to + 75 °C. ACRYL-W has an excellent price/performance ratio, can be painted over with water-based or solvent-based paints and has perfect adhesion without primer on most substrates, even slightly damp ones. ACRYL-W is easy to apply, virtually odourless and non-corrosive in combination with metals.

STUC-O-SEAL is a ready-to-use, plasto-elastic and age-resistant one-component joint sealant on acrylic resin basis with a structured, rough and plaster-like surface for interior and exterior use. STUC-O-SEAL is characterized by high weather and light resistance and remains permanently elastic over a very wide temperature range from -20° to + 75 °C. STUC-O-SEAL can be painted over with water-based or solvent-based paints and has perfect adhesion without primer on most substrates, even slightly damp ones. STUC-O-SEAL is easy to apply, virtually odourless and non-corrosive in combination with metals.

ANTI-CRACK is a high-quality acrylic joint sealant that reduces cracking and discolouration of paintwork and remains permanently elastic over a very wide temperature range from -20 °C to +75 °C. ANTI-CRACK can be painted over with water-based or solvent-based paints and has perfect adhesion without primer on most substrates, even slightly damp ones. ANTI-CRACK is easy to apply, virtually odourless, free from phthalate plasticisers and non-corrosive in combination with metals.

HIGH-TACK ULTRA is an extremely high quality adhesive for professional use and is suitable for bonding building materials in construction as well as materials in industry. It offers excellent weather and moisture resistance and remains stable over a very wide temperature range from -40 °C to +90 °C. HIGH-TACK ULTRA is based on a hybrid technology that cures to a permanently elastic and rubber-like adhesive when exposed to moisture. HIGH-TACK ULTRA is virtually odourless, is non-corrosive in combination with metals and impresses with an extremely high initial adhesion, is non-staining and free from isocyanates, phthalates, solvents and silicones.

HYBRIFIX-SEAL is a ready-to-use, permanently elastic and paintable one-component assembly and sealing compound based on hybrid technology, which hardens to a permanently elastic rubber compound when exposed to moisture. It offers excellent weather and moisture resistance and remains stable over a very wide temperature range from -40 °C to +90 °C. HYBRIFIX-SEAL is characterised by low shrinkage, shows enormous elongation at break and movement absorption capacity and adheres perfectly to most substrates, even damp ones. HYBRIFIX-SEAL is virtually odourless, non-corrosive to metals and free from isocyanates, solvents, phthalate plasticisers, tin and silicones.

Acryl W is a paint compatible, elastic sealant based on an acrylic emulsion. The product is virtually odourless and non-corrosive to metals. Acryl W is suitable for indoor and outdoor use, e.g. joints between wooden, metal window frames and concrete, masonry, gas concrete, metal, anodised aluminium and hard PVC, joints on stairs, walls, concrete and ceiling elements, skirting boards and window sills. The SOS Pressure Pack is used without a putty gun.

For outside and inside. Waterproof, extremely elastic jointing material on a 1-comp. basis. Application: Filling, filling, fixing, gluing and sealing of wood, metal, glass, plaster as well as for concrete, lime and cement substrates. ARTEKO ELASTIK is resistant to alkaline influences.

Permanently elastic premium silicone-based sealant for sealing connection and expansion joints for almost all building applications. Suitable for all standard building substrates indoors and outdoors, including marble, terrazzo, natural and sensitive artificial stone. Can also be used for bonding and grouting mirrors. Properties: Permissible total deformation 25 %, corrosion-neutral and solvent-free, compatible with natural stone, suitable for areas close to foodstuffs and in clean rooms, high UV and weather resistance, contains fungicidal agents against mould, reduced oxime odour and MEKO-free.

One-component PUR foam, for filling and insulating joints, cavities and wall openings. Completely fills the cross- section by expansion during foaming. The foam can is to be processed with the tube adapter or with a gun. Yield 38/42 litres, filling foam with good insulating properties, building material class B3 (DIN 4102).

For filling and insulating joints, cavities and wall openings. Suitable for window and door installation. Fills the cross-section completely and in a controlled manner by expansion during foaming. Optimum adhesion to common building materials. Suitable for increased pressure loads. The reaction during curing is independent of air humidity. Foam fabre light green, yield approx. 10 litres free foamed. Building material class B2 (DIN 4102).

For removing fresh foam splashes and cleaning the foam gun. Contains solvents.

Highly developed and fast curing 2-component universal putty with excellent direct adhesion on substrates such as galvanised or hot-dip galvanised sheet metal, steel, iron, aluminium, wood, stone, ceramics as well as on most commercially available plastics. BRICAPOLY can be applied easily and without pores (up to approx. 10mm layer thickness), is extremely fast and easy to sand (after approx. 20 minutes). BRICAPOLY can be painted over with all commercially available water-thinnable or solvent-containing 1- and 2-component products. Due to the styrene-reduced formulation, BRICAPOLY does not fall into the group of chemicals class 2. For resale, this means that no expertise course and related advice is required.

Extremely adhesive and fast curing 2-component fibre putty consisting of a mixture of high-quality and elastic polyester resins and glass fibres. Suitable for reinforcing rusted sheets and profiles and for bridging holes and cracks on steel, tinned bodywork sheet metal and glass fibre reinforced plastic. BRICAPOLY can be painted over with all commercially available water-thinnable or solvent-containing 1- and 2-component products. Due to the styrene-reduced formulation, BRICAPOLY does not fall into the group of chemicals class 2. For resale, this means that no expertise course and related advice is required.

BRICAPOLY is an aluminium-containing and elastic 2-component filler and surface filler and achieves heat resistance up to 100 °C. It is suitable for the repair of damaged areas that are exposed to strong vibrations, such as in the automotive repair sector, bodywork and vehicle construction, industrial and plant construction, as well as boats and caravans. BRICAPOLY can be applied easily and non-porous over large areas, can be sanded quickly, easily and with little dust. BRICAPOLY can be painted over with all commercially available water-thinnable or solvent-containing 1- and 2-component products. Due to the styrene-reduced formulation, BRICAPOLY does not fall into the group of chemicals class 2. For resale, this means that no expertise course and related advice is required.

High-quality 2-component polyester resin for bridging and reinforcing holes and cracks with glass fibre fleece, mat or fabric on vehicles, caravans, boat and model building, containers and GRP parts. Due to the styrene-reduced formulation, BRICAPOLY does not fall into the group of chemicals class 2. For resale, this means that no expertise course and related advice is required.

High-quality 2-component polyester resin for bridging and reinforcing holes and cracks with glass fibre fleece, mat or fabric on vehicles, caravans, boat and model building, containers and GRP parts. Due to the styrene-reduced formulation, BRICAPOLY does not fall into the group of chemicals class 2. For resale, this means that no expertise course and related advice is required.

Multi Blue is a polyester putty of the latest generation. State-of-the-art fillers, very thixotropic properties, optimum sanding properties and up to 20 % higher removal volume compared to conventional fillers. Very good direct adhesion on aluminium and steel surfaces, on galvanized steel sheet as well as polyester laminates and wood. BRICAPOLY can be painted over with all commercially available water-thinnable or solvent-containing 1- and 2-component products.

Hardener tubes for BRICAPOLY polyester putty.

BRICAPOLY can be applied easily and non-porous over large areas, can be sanded quickly, easily and with little dust. Very good direct adhesion on aluminium and steel surfaces, on galvanized steel sheet as well as polyester laminates and wood. BRICAPOLY can be painted over with all commercially available water-thinnable or solvent-containing 1- and 2-component products.

Hardener tubes for BRICAPOLY polyester putty.

AKEMI repair resin with adhesive additive is a mixture of unsaturated polyester resins dissolved in styrene and a special adhesive additive.

BRICACAR is a paste-like and asbestos-free filler for the repair of holes and cracks in exhaust systems.

For the household and for handicrafts. Glues paper, cardboard, wood, leather, fabrics, artificial leather, foam, cork, etc. Apply CREAFIX on one side and join immediately.

BLANCOL is a water-dilutable and colourless wallpaper primer for problematic surfaces. It consolidates the substrate to be wallpapered, prevents crumbling and regulates the suction power. Strengthens the adhesion of the wallpaper and helps to prevent wallpaper peeling. Does not attack solvent-sensitive polystyrene insulations.

For wallpapering paper and woodchip wallpaper. Also suitable for making masks, figures and objects from paper pulp and for fixing wallpaper.

Hard foam adhesive for insulation boards in the interior. High initial adhesion and secure adhesive strength. Also suitable for humid rooms.

Special paste with methyl cellulose. For heavy wallpaper and woodchip wallpaper that can also be dry stripped.

The non-ageing spray adhesive adheres immediately and securely, is colourless, leaves no stains and can be repositioned during the bonding process.

For bonding building materials with large bonding surfaces as well as insulation boards, dry construction boards, wooden constructions and masonry blocks. Rapid curing and therefore rapid further work. Levels out unevenness. 1 can corresponds to approx. 25 kg of adhesive mortar. Cures after 2 hours.

Mat made of pressed glass fibres is characterised by a high inherent stability. Serves to repair holes and more severe damage to corners, edges and curves in metal and GRP parts in combination with laminating and repair resin.

Consists of braided glass fibres. Used to repair holes in combination with laminating and repair resin on car body and GFRP parts that are exposed to high loads.

Pressed glass fibre fleece without inherent stability to achieve fine and smooth surfaces. In combination with the repair resin, it is suitable for repairing minor damage to GRP parts.

Mat made of pressed glass fibres is characterised by a high inherent stability. Serves to repair holes and more severe damage to corners, edges and curves in metal and GRP parts in combination with laminating and repair resin.

Consists of braided glass fibres. Used to repair holes in combination with laminating and repair resin on car body and GFRP parts that are exposed to high loads.

Additive for water or solvent based products for bridging small cracks. Add 300g per 20 kg bucket.

KOBAU glass fibre joint corner strips are used to bridge joints in dry construction with plasterboard or wood fibre boards. KOBAU glass fibre joint corner strips are joint tapes made of glass fibres. Can only be used indoors.

Fabric strip made of glass fibres as joint crack tape for filling over panel joints in dry construction and for cracks. Alkali-resistant, self-adhesive on one side, thickness 0.2 mm - 0.3 mm.

As a fabric insert in full thermal insulation facades (VWS) and reinforcement in thin-layer plasters. Tested according to ETAG No. 004. Alkali-resistant, displacement-resistant, mesh size 4 x 4mm.

Fabric angle with perforated PVC edge protection. Ideal for full thermal insulation facades. Mesh size 4x4mm.

Extruded polyethylene foam PE round cord with closed cell structure and smooth surface. The fine pores give the product an extremely smooth character. Suitable for backfilling the joint sealant in expansion joints, for connections of window and door frames, for dilatation joints of buildings, retaining walls and for connection joints in bathrooms, kitchens, floor coverings, etc.

Cork strips are best suited for elastic connection to other components and provide the necessary sound insulation.

For the removal of old and compacted dispersion layers. For alkali-resistant floors, such as PVC and stone. Low-odour, as it is ammonia-free.

Leaves behind a dirt-repellent film, without layer structure. For all glossy, coated, but also uncoated floors. Powerful cleaning in combination with perfect care.

Leaves a pleasant orange scent when cleaning. Also suitable for glossy surfaces, pH-neutral adjustment. Can be used both as a floor and surface cleaner.

For the efficient cleaning of all glass and mirror surfaces. There are no cleaning strips. Set ready for use.

Also removes rust runs and flash rust. Dissolves lime and urine stone, mortar and iron residues. Gently cleans stainless steel.

Powerful basic cleaner with the pH value of an all-purpose cleaner. For all water-resistant floors, also suitable for linoleum. Low-foaming, therefore also suitable for use in automatic machines.

For all shiny and matt floors. Leaves no visible residue. Ideal for rubber / and rubber studded floors.

For alkali- and alcohol-resistant floors, such as PVC and stone. For extremely heavy and greasy soiling. Excellent cleaning performance.

Cares for, cleans and protects stainless steel. Leaves a beautiful shine on the surfaces.

The 3M™ Scotch-Brite™ EssentEco Microfibre Cloth 2012 consists of a highly active microfibre and easily removes dirt, dust, oil, grease and fingerprints. Particularly suitable for efficient cleaning of metal, wood, glass, chrome, plastic, ceramic and marble. It can be used dry or damp, with or without cleaning chemicals. Washable up to 95°C. No risk of confusion of the area of application due to colour coding.

The durable cleaning cloths are extremely absorbent and can even be used several times without tearing. As a result, the consumption of cleaning cloths is reduced. These cleaning cloths fit into the Tork single cloth dispenser. As the cloths are not particularly fluffy, they are ideal for sensitive surfaces. Non-woven, 1-ply, unembossed, white.

Thanks to its high capacity, this roll towel is the ideal solution for busy toilets. The single sheet dispenser helps to minimise consumption and ensures hygiene because only the sheet to be removed is touched. The paper is highly absorbent and very soft. This towel is characterised by its high quality.

Tork Zigzag Towel Universal is a soft and high-quality folded towel, suitable for Tork Zigzag dispensers. The single sheet dispensing helps to minimise consumption and ensures hygiene because only the sheet to be removed is touched.

Highly absorbent and tear-resistant cleaning cloth rolls for soaking up liquids, cleaning surfaces and wiping hands. Roll of 500 sheets.

The Wypall L20 Extra wipes can be used universally and are suitable for medium-duty cleaning tasks, polishing glass, cleaning tools and wiping smooth surfaces. The wipes have a high absorption capacity of liquids and are ideal in areas with high consumption, as the wipes are economical in use. Roll of 500 sheets.

Kimtech Pure wipes can be used universally and are suitable for dry cleaning of surfaces in the pharmaceutical, biotechnology, medical device manufacturing and food sectors. The particularly powerful wipes are supplied in water-resistant bags.

Tork cleaning cloths are suitable for wiping up all surfaces and protect hands from heat and metal shavings. They have a high absorption capacity for oil and liquids and are also extremely tear-resistant. Roll of 750 sheets.

The standard cleaning cloths are suitable for simple wiping work and for wiping hands. The wipe roll is compatible with all Tork internal dispensers of the M2 system. Certified for contact with food. Recycled, 1-ply, inner roll, unperforated, unembossed.

The extra absorbent household roll is ideal for the usual wiping work on surfaces and for wiping up water, oil and food residues. The surface dries quickly. Roll of 51 sheets.